Listed here in the next paragraph you might get a lot of really good answers concerning A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough project. If the old bathtub is conveniently accessible, the project can move speedily; if you have to open up a wall to remove the old tub and place the new tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the job and also are comfortable attempting it. As opposed to working with a professional to take over a halfway-completed project, it is much better to consider employing one before you start. Chances are you may need an expert plumber to make tube links.
This post will aid you set up a new tub in your bathroom if you have actually already bought a brand-new tub and also do not need to transform the setup of your previous water pipelines.
Your tools and material list must make up the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bathroom needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you should do is separate the supply of water. After doing so, activate the taps to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be fairly problematic due to the limited access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little points.
The following objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bathtub till the spirit level reviews degree.
To mount taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Switch on the water supply and inspect all joints and new pipework for leakages as well as tighten them if essential. Fill the tub and also examine the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been made use of a minimum of when as this will certainly settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Protect the tap in position with the supplier provided backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and also the tiling, resulting in issues with moisture and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and cartridges, and also can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always load the tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealer can break relatively very early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly readily available on the market. It is recommended to fit the floor tiles utilizing waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog entry about Installing A Bathtub when doing research the web. Sharing is good. You never know, you might be doing someone a favor. Kudos for your time. Visit us again soon.
We're on standby!